J-B Weld 50112 ClearWeld 5 Minute Set Epoxy Syringe - Clear - 25 ml, 25ml

I've used JB Weld's ClearWeld for years, and it's never failed me. I've yet to find anything I could not fix with it. I've repaired and glued together: ceramics, plastics, wood panels, metal brackets, rubber, cloth and fibrous materials. I've also attached many of those items to one another with ClearWeld.Is there any material ClearWeld won't stick together? Maybe, but I have yet to have that happen.The most recent item I repaired were my eyeglasses. The left-side hinge had broken and there was no way to replace it — short of buying another set of frames. To fix them, I applied a thin layer of ClearWeld and held the frame hinge and its temple (the arm) together for a couple of minutes. After it setup, I let it sit for a few hours. When I came back, I was surprised to see that I could flex the eyeglasses without the frames separating at the hinge point. A $6 tube of ClearWeld, saved me the cost of a new set of frames.What Issues Does It Have?1. If you used too much, it takes a longer to cure.2. It does smell a bit. However, the smell doesn't bother me.3. A few customers have had the syringes leak during shipping. I've never had that happen.4. A few times, I've had more of the two-part epoxy come out of one side of the syringe than the other. It usually happens with a new syringe because one side binds up a bit as you're pushing on the handle. If that happens to you, just scrape away the excess to keep the mix ratio at 1 to 1.For me, ClearWeld has always dried hard. It's not rubbery when mixed properly.HINTS:A 45 degree, counter-clockwise turn and pull on the gray knob opens the syringe. CAUTION: Sometimes, the epoxy will be under some pressure, due to heat, (if it's summer time) and some of it might ooze out of the syringe — so be prepared to catch the excess with a paper towel.If you're going to be doing a big job and using lots of ClearWeld, do it outside. As the smell can be irritating to some people. Plus, the smell sticks around a lot longer.Do not over apply ClearWeld — use just enough to get the job done. ClearWeld bonds and works best when it's applied in a thin layer. That's what I did when I recently attached four hard rubber feet to the casing of a 2000 watt inverter. The aluminum housing had been anodized, and I wasn't sure if ClearWeld would bond the feet to the smooth surface. But it did! (I thought about drilling holes into the casing to mount the feet but didn't want to risk damaging the inverter.) After applying ClearWeld, I put some lead weights on the feet and let them dry overnight. The next day, I tried but was unable to pull any of them off with my fingers.ClearWeld is my go-to cure for fixing anything that's broken, has come apart or that I want to stick together. I highly recommend it.

We bought this to repair some 3/8", non-structural panel on our boat. It did a nice job. We opened the gap a bit and coated both sides of the break. Then relaxed what was holding the two parts separate, and it forced epoxy out both sides. We carefully removed the excess epoxy, and let it harden. Didn't disturb until the next day. You can still see the break location, but the repair appears to be holding well. Well worth the cost, and easy to mix and apply. Would buy again.

I recently used this product to set steel rods into newel posts for an interior railing. I needed something that would set very strong given the safety implications of my project, and JB Weld fit the bill perfectly. I have some more rods to set, so finding a cheaper price on Amazon vs. the big box hardware stores was great.Working time / setting time: I saw several reviews say this takes 10-15 minutes or more. I had the exact opposite experience. Mine became tacky and gummy so quickly (3-4 minutes) that I had to get my items glued with hustle. I worked in small batches using little paper cups after losing a relatively large first batch to the quick drying. It's dry where I live, so maybe humidity comes into play and could explain the large variance between reviewers. I'm not sure when my items were fully set, as I didn't want to test them too early and damage the initial bond.Adhesion / strength: I glued steel into wood and steel into MDF, and both bonds are holding extremely strong. I had to remove one of the rods to fix some paint and it was quite difficult to get out - exactly what I was looking for. I initially used some classic gray JB Weld, which I think is potentially a bit stronger (just my objective feel, not sure if that's true), but I didn't want any gray to leak or show on my railing. The clear is holding plenty strong for my purposes. Don't expect JB Weld to replace real welding, however. It's still surface adhesion, so it has its limits. There are some great videos online showing you how strong this stuff really is when tested for torque, shear weight, etc.Clarity: Dries very clear, no issues whatsoever. The gray was making a mess on the white newels for my railing, but the clear is nearly invisible. I can see tiny spots where I spilled if I look closely, and they're easy to chip off with a razor.